thumb 2018 09

40 Years of fun!

LOGO 40 Trans

Support our sponsors

Click above to visit their site!

Zone 1 Autocross

Retrofitting pre-1974 Hot Air Blower

Retrofitting pre-1974 Hot Air Blower

Shortly after introducing CIS fuel injection in 1974/1975, Porsche changed how hot air was sent into the passenger cabin for heat and defrosting.  Starting with the first 911 in 1965, the original air system consisted of a duct on either side of the fan housing routing air through the engine tin to the heat exchangers. The new mid-70's system consisted of a fan mounted high on the left upper side of the engine bay, with 3 hoses, one for an air intake from the fan housing, and two hoses from the blower through the engine tin to each heat exchanger. Backdating the air system to the older style is easy to do, and Porsche sells the parts you'll need, or you can visit your favorite used parts dealer.


You'll need the following parts:

Left hot air duct, 930.106.321.02, list $148.20
4 plastic nuts, 999.591.592.40, list $.12 each
2 rubber plugs, 999.703.044.50, list $.77 each
Right hot air duct, 911.106.327.00, list $53.45
Right engine cover plate, 911.106.036.00, list $14.89
Right engine cover, 911.106.827.00, list $5.04
Right air duct support, 911.106.331.00, list $1.30
Hose (see below)

The left hand air duct has a bunch of holes in it to fit 911's and 930's, and the rubber plugs and plastic nuts cover those holes and allow other things to be screwed to the housing. I put a screw into each plastic nut to pretty well close off those holes. The left hot air duct is metal, and the right duct is plastic, while the engine cover and plate are metal. The right air duct support is to bolt the right air duct to the larger plastic cover over the engine. I didn't use it, as things seem tight enough without it, however, we'll see if over time I need to add the support.

Installation is straight forward, take the existing blower and hoses out of the engine. On my 81SC, the bracket that holds the motor also holds one of the vacuum pipes, so I took the whole bracket off, and cut off the portion which held the motor, leaving the portion that holds a support for the pipe. Put the left hot air duct in. On the right, unscrew the cover plate and remove it. Put in the engine cover plate, followed by the right air duct, followed by the engine cover. The right air duct has some grooves in it where the engine cover cinches it up fairly tight.

Hoses: I used 4 feet of 2 1/2" SCAT hose (silcone rubber-based, good to 450 degrees) from Aircraft Spruce and Specialty, cost $21. You'll cut two pieces for the left side (duct to engine tin, then below engine tin to heat exchanger) and one longer piece on the right (duct to heat exchanger). I've also seen an aluminum-based hose used, as well as other types and colors. The hose has to stand the heat in the engine compartment and more importantly the heat at the heat exchanger connection.

That completes the installation. Assuming your heater boxes are working, and the wires to the heater controls on the floor are also intact, you're done! Not much heat at idle, it picks up well as the revs increase. If you open a window just a crack, then that helps the heated air move into the compartment.  And, especially if you've removed your air conditioning compressor, you can now see alot more of the engine.

There are many many places the club can use your help. If you have an interest in helping the club continue the great events for you, please consider contributing your time and expertise.

Jeff Torrey and I will serve as the 2019 nominating committee and our task is to find and interview qualified candidates for the elected offices of NCR: Vice President and Secretary.  The only qualifications for office are that you must be a member in good standing with PCA / NCR and you must have a strong desire to help shape the future of the club.

We will also accept any names you might have for the various committees that are vital to the Club.  These are appointed positions so we will pass the names to the President for further consideration.

Please contact Ivy 603-767-6461 if you are interested in serving or nominating someone for one of the elected positions or if you have a suggestion for any Board position or Committee Chair.

Nominee Statements and Ballots will be circulated to the membership for final voting in October.  Election results will be announced at the Annual Meeting / Banquet in November.

Thank you for your ongoing support and participation in this important process.  

Ivy Cowles – NCR Nominating Committee Chair